Tags

Austrailia, Cane, Chairs, Eucalyptus, Eucalyptus Chairs, Eucalyptus Furniture, Fiber Rush, Furniture, Genuine Rush, Hand Crafted, Oak, Pressed Cane, Rush, Word Press Problems

Eucalyptus Chair-Australia

Well the week ahead looks like we will be honing our skills on pressed cane and rush seats. In the studio we now have several oak chairs with pressed cane seats, in addition is several nice chairs from a customer in Northern Virinia, that were aquired while they were living in Singapore. These chairs were hand made in Australia and are of Eucalyptus Wood, they are finely detailed with Queen Anne Legs. These chairs are very elegant and have pressed cane seats, as well as backs, however just the seats need replacing.

There are also a pair of Oak dinning room chairs with small pressed cane seats, typical of this style of chair, as compared to the Eucalyptus chairs above, which have the entire sitting area of the chair in pressed/sheet cane.

The final chair in the studio in pressed cane is a black dinning chair, which need gluing and clamping in several places before the seat is replaced.

The Rush chair on hand to do at this time are Hitchcock in design, one having the drop in seat, meaning tht the framework that the rush is done on pops out of the chair, it is re-rushed and put back and held in place with screws. The second originally done in genuine rush (you twist the rope itself by hand) from cattail leaves into a hand twited rope and rush the chair from start to finish. This art while done years ago, has been widely replaced by the use of Fiber Rush (a tightly twisted brown kraft paper) that forms a rope, from that it is woven onto the seat or drop-frame. Asa “Genuine Rush is costly and time consuming and is usually reserved for heirlooms and museum quality work in today’s world.”

Oak Pressed Cane Chair

Seat Detail

The second picture shows a broken side piece that needs to be glued, and clamped and screwed back into place before the cane can be installed.

The two pictures on the left show an Oak Chair, which the pressed cane has totally worn out.

When the new cane has been installed, the cane will be stained to give it an aged appearance.

Rush Seats

Next on the list for this week is the replacement of two rush seats. One having a genuine rush seat that has deteriorated and will be replaced with Fiber Rush. Hitchcock style chairs usually incur a dis-assembly/re-assembly charge, as you have to remove button covers in the rear of the chair, also prying out wood strips from around the chair and removing a front decorative piece that is screwed into place, this forms a decorative as well as protective frame work around the rushed interior of the seat. All of this takes time to do just to get to the seat itself before rushing can take place.

The second chair has what is known as a drop in seat, it has been rushed with fiber rush that has worn and broken on the front rail, this is the common place for most rush to weaken and brake, as it gets all the weight and pressure from the thighs rubbing along the front edge of the seat. The interior of this seat is removable, however in some ways it it makes it more difficult over the rushing taking place directly on the chair rails itself.

Hitchcock Style Genuine Rush Chair

Hitchcock Style Genuine Rush Close Up

Note the back, side and front wood trim that needs to be removed and replaced in order to get to the seat to be woven.

In some cases there are wooden dowels or buttons in the rear behind the seat that need to be removed, that cover screws to release the wood frame on this type of chair.

This seat is not that way, most of those have heavier wide trim going around the seat.

Underside of Genuine Rush Seat

The next chair is the Hitchcock style with the removable drop in seat, where the inner frame must be removed in order that the rushing can take place, while this seems to be a simple task, it is much easier to re-rush in the chair frame. Nails or small strips or blocks of wood need to be tacked into place where the top of the leg posts would be normally, this is to hold the new rush in place until the finished seat can be replaced into the chair.

Drop In Rush Close Up

Modern day manufacturer’s of Rush Style Chairs, that specialize in mass production often resort to the drop in seat, as the chair can be manufactured in one country, and the seat in another or in another totally separate area of the factory, the assembled in another.

Premium furniture manufacturer’s such as Suter’s Hadcrafted Furniture- Harrisonburg, Virginia and Chlore”s of Madison, Virginia still rush the chairs they make right in the chair and do not use drop in frames. I am sure there are many others, however this is still done mainly by manufacturer’s of Hand Crafted Furniture, not neccessarily mass produced.

Pictures of the finished chairs will be posted in a separate post, later this week.

Please Note: The layout of this article is not the way it is supposed to be. I have found that Word Press has a mind of its own. It shows you what you think you will get, publishes something entirely differnt. Please be patient until I can find out how to correct this.

Tags

antique, Bottoms, Caning, Chair, child's rocker, drop-in seats, Fiber, Fiber Rush, Hand Caning, Herringbone Twill, hickory, Hitchcock Chair, Oak, photo's, Reed, rocker, Rush, Splint, studio

Child's Oak Rocker

This week is starting off with a mixed day of different seat weaving styles here. While most people unknowingly lump all seat weaving styles into the one catagory of “Caning” or “Hand Caning” each actually has different names.

Today I will be working on the 3 major styles. These Styles are Hand Caning, Splint Bottoms, and Rush. In the studio now is a hand caned side chair, an old childs antiques rocking chair, which has a splint bottom seat, and two Hitchcock style side chairs. One needs the original “Genuine Rush Seat” replaced with Fiber Rush, a tightly twisted brown kraft type paper in a rope like form. The second Hitchcock style chair is a newer version, which has what is known a s a Drop-In seat, meaning that the Rushing is done on a wooden frame separately from the chair, then when done the seat is placed back into the chair.

Child’s Oak Splint Bottom Rocker

The following photo’s show the rocker the way it came to the studio, the seat appeared to be Hickory, though worn and deteriorating. This set of photo’s will show “Before, During and After” replacing the old bottom with the new reed splint bottom, in the 3/3 Herringbone Twill pattern. More pictures will be added to this post, as they become available.